PEX-Systeme - Seite 2

Adapterwinkel PPM Uponor 1x3/4.

Transition from 18 mm to pipe thread.

Uponor 1042331 Sanitärarmatur Endzufuhr-Reduzierer

Manifold i gunmetal, used with female plastic pipe fitting

used for Roth manifold in gunmetal

Adapter gerade ppm Uponor 1x3/4.

Tool for fix of floorheating pipe

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

For assembly of pipes or fittings.

Adapter für die Verwendung mit dem PPM-Verteilersystem. Maximaler Druck: 10 barMaximale Temperatur: 70°CDie Montage des Adapters und des Verteilers erfolgt ohne Werkzeug mit einer Bajonett-Kupplung.

Used for Pex and CU pipe

Uponor Adapter mit männlichem Gewinde 1" und weiblichem Gewinde 3/4" für Q&E PPM.

Uponor Kupplungsbox doppelt M4 15X1/2

Mehrfachverteiler für Wasser mit 2 Auslässen. Inklusive 15 mm Anschluss für Polyethylenrohr mit TEA-Oberfläche.

Transition from 18 mm to pipe thread.

Used for assembly of pipe, pipe in pipe

Kupplung aus Messing mit TEA 3/4 x 1/2

HENCO VISION Messing-Nippeladapter 26 x 3/4 für Verteilerrohre für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

Wavin RADIATOR TRIM SET 15X1/2 F/PEX SHORT

For 2 pipe, in 15 mm

Mehrfachverteiler aus DR Messing. Mit Druckfittings geliefert.

Used for Roth QuickBox on wall in PVC

Fitting in gunmetal for Roth manifold